If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
mounting inkjet prints
I print using an Epson 2200 printer, which uses pigment inks. Is it
safe to use a drt mounting press on these? If not, what is a good archival mounting method? Thanks in advance for any help. |
#2
|
|||
|
|||
mounting inkjet prints
Mort wrote:
I print using an Epson 2200 printer, which uses pigment inks. Is it safe to use a drt mounting press on these? If not, what is a good archival mounting method? Thanks in advance for any help. AFAIK, with pigment ink prints, treat them much the same as with wet-process colour photo prints. One proviso is that it takes a while for pigment ink to dry - although they are reasonably water resistant within a few seconds of coming off the printer, they are relatively easily scratched until the coalescing solvents (glycol ethers) evaporate. That may take hours / days, depending on temperature, humidity, airflow around the print etc. |
#3
|
|||
|
|||
mounting inkjet prints
"Mort" wrote in message ... I print using an Epson 2200 printer, which uses pigment inks. Is it safe to use a drt mounting press on these? If not, what is a good archival mounting method? Thanks in advance for any help. Hi. I know of people who dry mount Inkjet Prints, but they do take more precautions to protect from overheating the Print. Personally, I have never had any success with dry mounting using an ordinary Domestic Iron, but it must be better with the proper gear. I use the 3M Mounting spray, Red Can. I allow it to dry for longer than the instructions say, so that it is only tacky rather than very sticky. I then apply the Print to the board using considerable pressure from a 6 inch wide rubber covered roller. I protect the Print surface, while doing so with Silicon paper. I never have any problems with extra adhesive being squeezed out beyond the print edges, or with the edges lifting in warm environments. I do the spraying outside in the fresh air, and always hold my breath while doing so, because the solvents are not beneficial to your health. Roy G |
#4
|
|||
|
|||
mounting inkjet prints
On May 22, 3:49 pm, Mort wrote:
I print using an Epson 2200 printer, which uses pigment inks. Is it safe to use a drt mounting press on these? If not, what is a good archival mounting method? Thanks in advance for any help. If you use low temp mounting tissue for RC papers you should be fine. I prefer archival linen mounting tape, holds the print on the back board but doesn't totally adhere it. Only problem is if you have your print in an area with variable humidity, over years it can develop some dimpling. I have been using this with prints over 20 year and most of my prints have no problems, one older cibachrome has some dimpling, none of my prints form non silver processes (closest to inkjet) that I did in the '70s have any dimpling. One advantage to this is if you decide you don't like the print anymore you can reuse the matte and backing board. A 50 ft roll costs $20.00, for a 16x20 you use a foot or two for an 8x10 maybe 6 inches. Use the same tape on your matte if you aren't framing. Tom |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
mounting inkjet photos | Mort | Digital Photography | 1 | May 23rd 07 11:42 AM |
mounting and laminating inkjet prints | graceface | Digital Photography | 1 | October 8th 06 04:24 PM |
New inkjet print mounting technique | llamadave | Digital Photography | 6 | March 20th 06 04:45 AM |
Protecting inkjet prints | Robert Feinman | Digital Photography | 0 | October 14th 05 03:06 PM |
mounting inkjet prints | George | Digital Photography | 5 | January 23rd 05 09:43 PM |