If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Scanning glass mount slides
Presumably a film scanner cannot cope with a glass mounted slide, especially
the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? |
#2
|
|||
|
|||
ITMA wrote:
Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? I have done a little bit of experimenting with Gepe glass mounts, and drum scanning oil. The combination are then used in a film scanner. There is no patterning problem, the colours are easier to accurately capture, and the dynamic range seems to improve slightly. The only problem is this is a slow process. Without the drum scanning oil, I think the only reason to use a glass mount would be if the original transparency has curled badly. Ciao! Gordon Moat A G Studio http://www.allgstudio.com/gallery.html Updated! |
#3
|
|||
|
|||
ITMA wrote:
Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? I have done a little bit of experimenting with Gepe glass mounts, and drum scanning oil. The combination are then used in a film scanner. There is no patterning problem, the colours are easier to accurately capture, and the dynamic range seems to improve slightly. The only problem is this is a slow process. Without the drum scanning oil, I think the only reason to use a glass mount would be if the original transparency has curled badly. Ciao! Gordon Moat A G Studio http://www.allgstudio.com/gallery.html Updated! |
#4
|
|||
|
|||
Take tehm out of the glass mount while scanning. Unless they have stuck, of
course. -- http://www.chapelhillnoir.com home of The Camera-ist's Manifesto The Improved Links Pages are at http://www.chapelhillnoir.com/links/mlinks00.html A sample chapter from "Haight-Ashbury" is at http://www.chapelhillnoir.com/writ/hait/hatitl.html "ITMA" wrote in message ... Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? |
#5
|
|||
|
|||
Take tehm out of the glass mount while scanning. Unless they have stuck, of
course. -- http://www.chapelhillnoir.com home of The Camera-ist's Manifesto The Improved Links Pages are at http://www.chapelhillnoir.com/links/mlinks00.html A sample chapter from "Haight-Ashbury" is at http://www.chapelhillnoir.com/writ/hait/hatitl.html "ITMA" wrote in message ... Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? |
#6
|
|||
|
|||
Gordon Moat wrote in message ...
ITMA wrote: Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? I have done a little bit of experimenting with Gepe glass mounts, and drum scanning oil. The combination are then used in a film scanner. There is no patterning problem, the colours are easier to accurately capture, and the dynamic range seems to improve slightly. The only problem is this is a slow process. Without the drum scanning oil, I think the only reason to use a glass mount would be if the original transparency has curled badly. http://www.allgstudio.com/gallery.html Updated! I'm thinking about getting a 35mm film scanner to deal with my slides... approaching the digital age at a cautious pace! One newbie question, which I have never seen the answer to: does the autofocus feature on film scanners deal with moderately warped / curled slides? Thanks Ed |
#7
|
|||
|
|||
|
#8
|
|||
|
|||
|
#9
|
|||
|
|||
|
#10
|
|||
|
|||
Ed Blagden wrote:
Gordon Moat wrote in message ... ITMA wrote: Presumably a film scanner cannot cope with a glass mounted slide, especially the 'anti-newton' types which of course give a noticeable blurring when projected so would no doubt completely throw a scanner ...? Any experiences? I have done a little bit of experimenting with Gepe glass mounts, and drum scanning oil. The combination are then used in a film scanner. There is no patterning problem, the colours are easier to accurately capture, and the dynamic range seems to improve slightly. The only problem is this is a slow process. Without the drum scanning oil, I think the only reason to use a glass mount would be if the original transparency has curled badly. http://www.allgstudio.com/gallery.html Updated! I'm thinking about getting a 35mm film scanner to deal with my slides... approaching the digital age at a cautious pace! One newbie question, which I have never seen the answer to: does the autofocus feature on film scanners deal with moderately warped / curled slides? No, and the autofocus is not always the best choice for certain slides. Some scanners have a fixed DoF that covers a certain width of film, and might actually do okay with a slightly curved piece of film. It is better to find a scanner that lets you manually adjust the focus. Some films will give much better results by adjusting the focus slightly before, or slightly after, the point that the autofocus suggests. As a newcomer to this technology, you should also know that the default settings are not always the best choice. There is also an issue of the scan preview window not always giving an accurate looking (colour) preview, though better software often is very close. There is VueScan, which is fairly low cost, and works with many more common scanners, and at the high end is SilverFast. SilverFast is actually more capable, though much more expensive. Also, SilverFast will not work with all scanners. At the professional level, the idea is to get an extremely accurate scan, and not have any need for adjustments in PhotoShop (or whatever editor you use). Some film scanners have a good enough range of adjustments to allow that, but many do not, thus requiring adjustments to the scanned file. You might be surprised that some lower cost scanners are very good, though sometimes let down by the included software. Anyway, best of luck with your search. Ciao! Gordon Moat A G Studio http://www.allgstudio.com/gallery.html Updated! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
scanning 35mm color slides | 1iJack | 35mm Photo Equipment | 22 | September 3rd 04 06:02 AM |
Refining scanning slides with Epson CX5200 | Doc | Film & Labs | 1 | August 21st 04 07:22 AM |
Scanning 35mm Slides | MATT WILLIAMS | Film & Labs | 16 | July 2nd 04 08:41 AM |
Scanning Old Slides | MBP | In The Darkroom | 1 | February 3rd 04 07:00 AM |