A Photography forum. PhotoBanter.com

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PhotoBanter.com forum » General Photography » In The Darkroom
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

B&W film developing questions



 
 
Thread Tools Display Modes
  #11  
Old January 5th 08, 10:56 PM posted to rec.photo.darkroom
____
external usenet poster
 
Posts: 534
Default B&W film developing questions

In article ,
"Lawrence Akutagawa" wrote:

There are folks who don't like Rodinal. That's okay. After all, some folks
don't like Chevrolets and others don't like Toyotas. The key is to try
Rodinal. If you like the results, great. If you don't like the results,
look for something else.


I my mind's eye Rodinal creates a tonal scale at 1;50 & 1:100 close to
PMK without the stain, so it ends up a little more grainy in appearance.
And of course less toxic.

--
Reality is a picture perfected and never looking back.
  #12  
Old January 5th 08, 11:02 PM posted to rec.photo.darkroom
____
external usenet poster
 
Posts: 534
Default B&W film developing questions

In article m,
David Nebenzahl wrote:

but you're not likely to get smooth-looking
results with Rodinal.


I think that really depends. Some films unquestionably are not going to
give the photographer tight grain "small clumps" when processed using
Rodinal. However T grain films should work well with Rodinal especially
when using 1:50 & 1:100 dilutions.

--
Reality is a picture perfected and never looking back.
  #14  
Old January 6th 08, 02:07 AM posted to rec.photo.darkroom
external usenet poster
 
Posts: n/a
Default B&W film developing questions


"Lawrence Akutagawa" wrote in message
...

My own prediliction is to decant the 500ml container into 1 oz (30 ml)
glass amber bottles.


Yep! The bottles with the expressed cap that displaces the last bit of
Rodinal. Air free. Done that way, Rodinal will last forever.


  #15  
Old January 6th 08, 02:37 AM posted to rec.photo.darkroom
Richard Knoppow
external usenet poster
 
Posts: 751
Default B&W film developing questions


"____" wrote in message
...
In article ,
(Thor Lancelot Simon) wrote:

The problem, of course, is that it also reduces true film
speed by as much as one full stop -- so in practice, you
end up with 50
speed film, at most, and then you need a tripod, unless
you're shooting
snowscapes at noon.


Define film speed Reduces? of just shows the speed of
older emulsions
for what they really are?

The published speeds of films are determined by a well
controlled standard method. The speed does vary with the
developer and the current ISO standard requires that the
published speed note the type of developer used for the
test. The total variation of speed with developer type is
not very great, its limits are probably no more than + or -
about 3/4 to one stop. The fastest speeds are obtained from
developers with Phenidone or its derivatives (but not all
Phenidone developers increase speed) such as T-Max and T-Max
RS, Xtol, or Ilford Microphen. The lowest speeds from
extra-fine-grain developers like Microdol-X or Ilford
Perceptol either at full strength. Developers like D-76 fall
into the middle somewhere with the speed increasing
developers yeilding about 3/4 stop more speed and the
extra-fine-grain developers about 3/4 stop less speed. When
diluted the extra-fine-grain developers mentioned above
deliver about the same speed as D-76 but loose their
extra-fine-grain property and deliver grain also about the
same as D-76.
Rodinal delivers somewhat less speed than D-76 but not
much, maybe 1/2 stop. Generally the underexposure latitude
of most films will accomodate this.
Note that the ISO standard is designed to calculate the
minimum exposure that results in good tone rendition of
shadows. The reason is to minimise grain, which generally
increases with density, and to maximize sharpness. sharpness
is decreased by "irradiation" which is the spreading out of
highlights in the negative due to internal reflection in the
emulsion. Modern emulsions are not as vulnerable to either
of these effects as the films made when the standard was
designed.
For many purposes the tone rendition can be improved by
increasing exposure a bit, usually reducing speed by about
20% will do it. But, of course, the exposure is due not only
to the film speed by the method of metering and decisions
made by the photographer as to what consitutes the shadow
areas of the scene being photographed where he/she wants
detail.
Note that the ISO standard being discussed applies only
to B&W still negative film, there are different standards
for motion picture films, color films, transparency films,
etc.
Rodinal is a good, general purpose, developer whose main
virtue is its convenience and reliability. It delivers good
tone rendition from most films at the cost of somewhat more
grain than developers like D-76 or Xtol but the T-Max
developers and Microphen are nearly as grainy.
Rodinal tends to produce somewhat finer grain when its
diluted. I generally use it at around 1:50 but that is also
to get convenient times for the films I work with.
My "standard" developer for most work is D-76 diluted
1:1 and used once. I also use Microdol-X or Perceptol full
strength for 35mm 100T-Max because the combination delivers
extremely fine grain with reasonable speed.


--
---
Richard Knoppow
Los Angeles, CA, USA



  #16  
Old January 6th 08, 03:00 AM posted to rec.photo.darkroom
Richard Knoppow
external usenet poster
 
Posts: 751
Default B&W film developing questions


"G.T." wrote in message
...
Ok, I just developed my first 3 rolls of film at home, and
except for a little bit of dust on the last roll the
results are excellent. I'll sporadically be developing
more over the next couple of months.

I'm using Rodinal, Arista's indicator stop bath, Arista's
Universal non-hardening fixer, and Kentflo.

Questions:

1. The Rodinal says undiluted it will last 6 months. Can
I be safe to assume it will last that long?

Also, with the Rodinal I've been developing only one roll
per mix because I'm new at this. With Accufine, the
previous developer I used, I would do a couple of rolls in
one canister before dumping back into my storage container
and replenishing. And after 3 months at the same
developing time my negs were a little light.

Can I develop more than one roll of film in my Rodinal?

2. The stop is the least of my worries, right? It should
be ok for a couple dozen rolls over the next couple of
months?

3. What's the expected longevity of the fixer?

Thanks,
Greg


Rodinal has a very long life. It can turn nearly black
and still work. The working solution should be used only
once and discarded. While the used developer will still
develop it will be hard to predict the results. However, if
the amount of solution is reasonably large you can probably
get a second roll by increasing time by about 20%.

You can re-use the stop bath in a single session as long
as it remains acid (the indicator will show this) but its
not good practice to save it between sessions.

Fixer has relatively low capacity for complete fixing and
complete fixing is important to the lifetime of the
developed film. The rule of thumb is to discard the fixer
when _clearing_ time has doubled but IMO this is stretching
things a bit. Clearing time is measured by fixing out a
scrap of the film you are working with. Soak the sample in
water for a couple of minutes before testing it because wet
film fixes at a different rate than dry film. Test a sample
when the fixer is first mixed and before its used. Note the
time it takes for the film to become completely clear. The
rule of thumb is to fix for twice this time and to discard
the bath than the clearing time doubles.

Unless you work with very small quantities of film its
best to use two successive fixing baths. The film or paper
is fixed in each bath for half the normal fixing time. The
first bath does most of the work leaving the second bath
relatively fresh so it can clean up any unfixed halide.
After the first bath becomes exhausted its dumped. The
second bath then becomes the first bath and a new second
bath is mixed. Kodak has full instructions about this in
their Darkroom Dataguide booklet.

In addition to your processing method outlined above I
would add the use of a wash aid. I prefer Kodak Hypo
Clearing Agent because Kodak has published the details of
its contents and experimental evidence that it works. I
believe that Ilford's wash aid is essentially identical. Teh
wash aid will reduce film washing time from about 30 minutes
to about 5 minutes. The wash aid can also remove some
otherwise insoluble fixer reaction products.

Use the wetting agent after washing as you are doing.
Because the wetting agent can collect gelatin from the film
and will support mold it should not be saved between
sessions. It can be used for more than one roll of film but
should be discarded after you finish working.


--
---
Richard Knoppow
Los Angeles, CA, USA



Similar advice applies to paper development.


  #17  
Old January 6th 08, 05:06 AM posted to rec.photo.darkroom
external usenet poster
 
Posts: n/a
Default B&W film developing questions


"G.T." wrote in message
...

Right, but I'm still too worried that I'll screw up 5 rolls at a time by
doing something really stupid like popping the top off of my tank while
agitating. Once I get on a roll I'll switch to my 3 roll tank.


Well understood. Enjoy.


  #18  
Old January 6th 08, 05:19 PM posted to rec.photo.darkroom
George Mastellone
external usenet poster
 
Posts: 10
Default B&W film developing questions

pico wrote:
"Lawrence Akutagawa" wrote in message
...

My own prediliction is to decant the 500ml container into 1 oz (30 ml)
glass amber bottles.


Yep! The bottles with the expressed cap that displaces the last bit of
Rodinal. Air free. Done that way, Rodinal will last forever.


I remember back a LONG time ago, Rodinal came in an amber bottle
with a rubber stopper under the cap. Since my father was a doctor, I
got a hold of a large syringe and needle and was able to extract and
measure small amounts of developer without ever adding any air to the
bottle.

I guess that can't be done anymore
  #19  
Old January 7th 08, 04:20 AM posted to rec.photo.darkroom
G.T.
external usenet poster
 
Posts: 692
Default B&W film developing questions

Richard Knoppow wrote:

Fixer has relatively low capacity for complete fixing and
complete fixing is important to the lifetime of the
developed film. The rule of thumb is to discard the fixer
when _clearing_ time has doubled but IMO this is stretching
things a bit. Clearing time is measured by fixing out a
scrap of the film you are working with. Soak the sample in
water for a couple of minutes before testing it because wet
film fixes at a different rate than dry film. Test a sample
when the fixer is first mixed and before its used. Note the
time it takes for the film to become completely clear. The
rule of thumb is to fix for twice this time and to discard
the bath than the clearing time doubles.


Thanks Richard. I'll have to do this. I was just using the times
suggested on the fixer bottle.

From reading your post and Lawrence's I can test by snipping off the
leader of a 35mm roll? Just drop it in some fixer and time how long it
takes to clear?

I also have a roll of 120 Tri-X 400 that I opened just to practice
loading a reel with.


Unless you work with very small quantities of film its
best to use two successive fixing baths. The film or paper
is fixed in each bath for half the normal fixing time. The
first bath does most of the work leaving the second bath
relatively fresh so it can clean up any unfixed halide.
After the first bath becomes exhausted its dumped. The
second bath then becomes the first bath and a new second
bath is mixed. Kodak has full instructions about this in
their Darkroom Dataguide booklet.

In addition to your processing method outlined above I
would add the use of a wash aid. I prefer Kodak Hypo
Clearing Agent because Kodak has published the details of
its contents and experimental evidence that it works. I
believe that Ilford's wash aid is essentially identical. Teh
wash aid will reduce film washing time from about 30 minutes
to about 5 minutes. The wash aid can also remove some
otherwise insoluble fixer reaction products.

Use the wetting agent after washing as you are doing.
Because the wetting agent can collect gelatin from the film
and will support mold it should not be saved between
sessions. It can be used for more than one roll of film but
should be discarded after you finish working.


So in this workflow it would be develop, stop, fix, hypo, wash, and
wetting agent? In class we washed prints in hypo but not film.

Oh, and regarding grain, my instructor actually suggested that I use
Xtol for now. But during class he told us that we'll get larger, more
noticeable grain if we using something like Rodinal/HC-110. That's why
I'm currently playing with it.

The bigger issue is that I'm getting used to developing at home but
there is no way I'm going to be able to print at home. Does anyone have
any current suggestions on finding a rental darkroom in LA these days?
I'm currently signed up for another B&W class in Burbank, but I'm not
going to have time to these next few months to actually do any
assignments, I just want to print stuff from the last 4 months.

I was thinking about calling up Translight Colors. Anyone heard good or
bad?

Thanks,
Greg



  #20  
Old January 7th 08, 06:13 AM posted to rec.photo.darkroom
Ken Hart[_2_]
external usenet poster
 
Posts: 23
Default B&W film developing questions


"G.T." wrote in message
...
snip
So in this workflow it would be develop, stop, fix, hypo, wash, and
wetting agent? In class we washed prints in hypo but not film.

Just for the record. "fixer" and "hypo" are basically the same thing. I
realize that when you say "hypo", you mean "hypo clearing agent"(sometimes
called "HCA"). The purpose of the hypo clearing agent is to remove the hypo
or fixer from the film or print.

Back in the 'good old days' when prints were actually paper and not
resin-coated plastic stuff, the paper print would soak up a lot of
chemicals. You needed to wash a print for perhaps an hour or so to remove
all the fixer from the porous paper. (Ricard K., please feel free to jump in
and correct me or elaborate-- I'm certain you are far more knowledgeable on
this!). A hypo clearing agent would neutralize the hypo (or fixer), so that
a shorter wash time (perhaps 30 minutes?) would suffice.

Film, being a non-porous material (or certainly less porous than fiber-based
prints) doesn't soak up as much chemistry, so a hypo clearing agent is not
as important. If it's critical to you that your negatives last to the next
millenia, than you may want to use it anyway...!

As for not being able to print at home, there are many people who make do
with printing in a bathroom. Some use a cart (Rubbermaid? Check office
supply or food service supply companies.) to hold their enlarger and store
their chems, trays, and stuff so they can wheel everything into the bathroom
for a session, then wheel it all into a closet for storage. You can put
velcro around the window frame and stick a piece of faric or cardboard over
the window. There is also a gentleman who espouses 'one-tray' processing.
I've never tried it myself, but perhaps for the temporary darkroom, it may
be the answer. Maybe someone here can supply the link to his website, or to
websites for temporary darkrooms. Using the kitchen is also a possibility,
but some people don't like that idea because of the possibility of food
being contaminated-- but for darkroom work, cleanliness is important, so
wipe up those chem spills!
For me, you can take away my permanent darkrooms when you can pry the
staticmaster brush from my cold, dead fingers!


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Developing film twice. Gregory L. Hansen 35mm Photo Equipment 17 December 15th 05 08:38 PM
Tray developing 4x5 - questions Stephan Goldstein In The Darkroom 18 October 15th 04 03:52 AM
Advice for camera bag, film developing and film choice JZ 35mm Photo Equipment 4 August 24th 04 08:56 PM
Film developing Tina In The Darkroom 24 July 24th 04 06:51 PM
400TX Developing Questions Adam Attarian In The Darkroom 15 April 9th 04 09:54 PM


All times are GMT +1. The time now is 02:07 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PhotoBanter.com.
The comments are property of their posters.